# Engineering Mechanics

#test International Conference

  Login

Proceedings Vol. 30 (2024)

ENGINEERING MECHANICS 2024

30th INTERNATIONAL CONFERENCE
May 14 – 16, 2024, Milovy, Czech Republic
;
Editors: Vladimír Fuis and Petr Hájek

Copyright © 2024 Brno University of Technology, Institute of Solid Mechanics, Mechatronics and Biomechanics, Brno

ISBN 978-80-214-6235-9 (printed)
ISSN 1805-8248 (printed)
ISSN 1805-8256 (electronic)

scientific commitee

keyote lectures

Dynamics of rotating systems focused on industrial applications
Hajžman M., Bulín R., Byrtus M., Dyk Š., Polach P., Rendl J., Smolík L., pages 18 - 23
Quo vado biomechanics
Sant Z., pages 24 - 35

papers

Influence of the etching time of Ti6Al4V titanium alloy with selected acid solutions on changes in physical parameters of the element
Abramczyk I., Ligaj B., pages 38 - 41
Turbulence estimation by eddy dissipation rate at low-altitudes using UAV in-situ data
Balážová R., Ferrari S., Hlinka J., Santus A., pages 42 - 45
Applying a two degree of freedom model for drive-by identification
Bayer J., pages 46 - 49
B-spline based density estimation of fatigue failures in SLM 18Ni300 steel
Blacha Ł., pages 50 - 53
CGA-based snake robot control model
Byrtus R., pages 54 - 57
Structural optimization using biological growth method in ANSYS Mechanical, part I
Čada Z., Černák M., pages 58 - 61
Structural optimization using biological growth method in ANSYS Mechanical, part II
Čada Z., Černák M., pages 62 - 65
New design and upgrade of whirl flutter aeroelastic demonstrator
Čečrdle J., Vích O., Stárek J., Vlach J., Kolář M., Šmíd M., pages 66 - 69
Thermal management for mission critical aircraft equipment
Červenka M., Koštial R., pages 70 - 73
Perspective ways of heat transfer enhancement for heat exchangers in fouling conditions
Chudý D., Jegla Z., pages 74 - 77
Weak imposition of potential Dirichlet boundary conditions in piezoelasticity: Numerical study
Cimrman R., pages 78 - 81
Design of a device for measuring the rate of particulate fouling of heat transfer surfaces
Daxner J., Jegla Z., Zabloudil J., Babička Fialová D., Reppich M., pages 82 - 85
Battery crash simulation in ANSYS LS-DYNA
Dohnal J., Šebík M., pages 86 - 89
PIV measurement of wakes past stator wheel inside air test turbine VT-400 in two axial×tangential planes
Duda D., Uruba V., Yanovych V., Klimko M., Tomášková T., Jeřábek M., Žitek P., Milčák P., pages 90 - 93
Probability limits of the critical rotor speeds
Dupal J., pages 94 - 97
Solution methods for an aeroelastic problem with combined harmonic and stochastic excitation
Fischer C., Náprstek J., pages 98 - 101
Assessment of mechanical properties of titanium samples, manufactured with the use of additive technologies
Gzik-Zroska B., Joszko K., Stradomski G., Piątek A., Wolański W., Kawlewska E., pages 102 - 105
Augmented M5 geometry of human vocal fold in phonatory position – pilot results
Hájek P., Horáček J., Švec J. G., pages 106 - 109
Analytical investigation of Mars drone conceptual design
Havran E., pages 110 - 113
On diffusion, reaction, and flow of high-concentration multicomponent gas mixtures
Hlavatý T., Isoz M., pages 114 - 117
Temperature field evaluation using injection mold thermal inserts
Holesovský F., Hejna M., pages 118 - 121
Stress-strain analysis of the EFZ–22 sand filter pressure vessel
Houfek M., Šimáček F., pages 122 - 125
Galloping of insulated bundled overhead line simplified analysis
Hračov S., Macháček M., pages 126 - 129
Manipulator trajectory and workspace in the MATLAB and MSC ADAMS environments
Hroncová D., Delyová I., Sivák P., Prada E., pages 130 - 133
Modelling of leading edge morphing by using geometrically exact beam theory
Hrstka M., Bajer J., Hadaš Z., Sharif Khodaei Z., Aliabadi F., Kotoul M., pages 134 - 137
Impact of different disinfection solutions on mechanical properties of orthodontic impress silicone material
Hrubanová A., Thomková B., Košková O., Richtrová M., Borák L., Štourač P., Marcián P., pages 138 - 141
Using finite volume method to simulate laser shock peening of 7050 Al alloy
Isoz M., Gruber P., Ježek O., Kubíčková L., Gabriel D., Kaufman J., Brajer J., pages 142 - 145
Influence of simplifying the geometry of the FE model of the vehicle frontal full barrier crash test
Jančář R., Dlugoš J., Fridrichová K., pages 146 - 149
Vibration diagnostics in the assessment of the vehicles bodywork technical state procedure
Kałaczyński T., Łukasiewicz M., Liss M., Mazurkiewicz A., pages 150 - 153
Data-driven approach to estimating soot distribution inside catalytic filters in automotive exhaust gas aftertreatment
Khýr M., Plachá M., Hlavatý T., Isoz M., pages 154 - 157
Dynamic properties of pressure compensated pump
Kolář D., pages 158 - 161
Design of cable-nets for glass façades
Komlev V., Machacek J., pages 162 - 165
Influence of Berkovich indenter tilt on the projected contact area at nanoindentation test
Kovář J., Fuis V., pages 166 - 169
Motion analysis of Czech sign language alphabet: CNN-based classifier via optical flow
Krejsa J., Vechet S., Šnajder J., pages 170 - 173
Reynolds-averaged simulation of turbulent flows with immersed boundaries
Kubíčková L., Isoz M., pages 174 - 177
Free axisymmetric vibration of elastically restrained porous annular plate using Haar wavelets
Kumar Y., pages 178 - 181
LES simulations of airflow around rectangle with side ratio 2:1 and their comparison with experiments
Ledvinková B., Hračov S., Macháček M., pages 182 - 185
Efficient computational algorithm for solving two-scale problems of large deforming heterogeneous periodic structures
Lukeš V., Rohan E., pages 186 - 189
Galloping of insulated bundled overhead line - nonlinear numerical analysis in time domain
Macháček M., Hračov S., pages 190 - 193
Structural damage detection by PSO method
Marton M., Sokol M., Lamperová K., pages 194 - 197
Aspects of adaptation of flange joints for modern low-carbon energetics
Michálková A., Jegla Z., Krišpín J., Gross A., Reppich M., pages 198 - 201
Modeling of a quarter-car model passing an obstacle using Laplace transforms, MATLAB/SIMULINK and SimScape
Miková Ľ., Šarga P., Vagaš M., Prada E., Brada L., pages 202 - 205
Reconstruction of duo rolling mill
Mrkos J., Horký P., Formánek M., pages 206 - 209
Stochastic version of the arc-length method
Náprstek J., Fischer C., pages 210 - 213
Micro-scale creep of cementitious materials
Němeček J., Němečková J., Němeček J., pages 214 - 217
Design of an indexing gearbox with radial cams
Ondrášek J., pages 218 - 221
Elastoplastic models for interpreting indentation results
Panfilov I.A., Aizikovich S.M., Vasiliev A.S., pages 222 - 225
Prediction of non-stationary deformation of gas turbine using machine learning approach coupling between CFD and FEM model
Pařez J., Vampola T., pages 226 - 229
Role of submembrane spaces in the control of transmembrane ion flux and cellular inotropic state in a model of human ventricular cardiomyocyte
Pásek M., Bébarová M., Christé G., pages 230 - 233
Degree of susceptibility of the gas-bearing coal massif to changes under vibration and technical solutions for increasing methane extraction from the reservoir
Pavlenko M.V., pages 234 - 237
Enhancing medical insights through computational fluid dynamics: Validating simulation model for blood flow in vascular system
Ples M., Wolański W., Sobkowiak M., pages 238 - 241
Investigation of the effect of surface texturing in hydrodynamic sliding contacts
Polach P., Smolík L., Byrtus M., Hajžman M., pages 242 - 245
Influence of sine-shaped profile deviations on static transmission error
Rackovský D.M., Czakó A., pages 246 - 249
Experimental investigation of fluid-structure-acoustic couplings by studying the resonance properties of vocal tract models with yielding walls
Radolf V., Horáček J., Košina J., pages 250 - 253
Enhancing sensitivity in piezoelectric micro cantilever designs using stress concentration regions for label free detection
Raziyan M.S., Janusas G., pages 254 - 257
Elastodynamics in periodic media – approximation by higher order homogenization and metamaterials with resonators
Rohan E., Naili S., pages 258 - 261
Concept of smart cymbal structure for structural health monitoring applications
Slabý V., Bajer J., Hadaš Z., pages 262 - 265
Non-linear probabilistic assessment of existing bridge considering deterioration
Slowik O., Šomodíková M., Novák D., pages 266 - 269
Investigation of 3D flow structures in a linear blade cascade with stereo particle image velocimetry
Šnábl P., Procházka P., Uruba V., Pešek L., pages 270 - 273
Influence of artery unfoldment on its mechanical response
Sochor O., Hrubanová A., Joukal M., Burša J., pages 274 - 277
Damage identification of small houses in different seismic regions
Sokol M., Crespo-Sanchez S., Rodríguez-Paz M., Mazáčková K., Gogová Z., pages 278 - 281
Acoustic emission methods in steel bridge degradation identification and monitoring
Šorm F., pages 282 - 285
Development and verification of novel dual plunger hybrid kinetic energy harvester
Sosna P., Hadaš Z., pages 286 - 289
Parallelization of DEM solver for non-spherical solids: A pathway to scalable CFD-DEM simulations
Studeník O., Kotouč Šourek M., Isoz M., Kočí P., pages 290 - 293
Non-stationary waves in thick elastic and viscoelastic plates
Šulda J., Adámek V., pages 294 - 297
Experimental assessment of the mechanical behavior of impression material for anaesthesiology use: A preliminary study
Thomková B., Hrubanová A., Košková O., Richtrová M., Skácel P., Štourač P., Marcián P., pages 298 - 301
Influence of dental implant insertion depth on strain in periimplant bone tissue
Thomková B., Borák L., Podešva P., Podešva M., Joukal M., Marcián P., pages 302 - 305
Design study of cooling for forward-type detectors under increased luminosity expected at the future LHC operating conditions
Vacek V., Petrášek Š., Horvath J., pages 306 - 309
AI-based assistive maintenance of machines via Querix expert-system
Vechet S., Krejsa J., Chen K.S., pages 310 - 313
Apparent Young's modulus of human cranial cancellous bone
Votava T., Marcián P., Borák L., Fuis V., Zikmund T., Kaiser J., Wolff J., pages 314 - 317
Prefabricated system for strengthening full-size wooden girders using pre-stressed fiber-reinforced polymers and steel – bending shear tests
Wdowiak-Postulak A., Świt G., Krampikowska A., pages 318 - 321
Construction of a modular device for testing high-temperature flue-gas fouling in waste-heat sources
Zabloudil J., Jegla Z., Daxner J., Babička Fialová D., Freisleben V., Reppich M., pages 322 - 325
Optimizing Venturi nozzle design for enhanced cavitation and pressure dynamics: A comparative analysis of turbulence models for cavitating flow characterization
Zeman R., Rudolf P., pages 326 - 329

Text and facts may be copied and used freely, but credit should be given to these Proceedings.

All papers were reviewed by members of the scientific committee. 






  

  

    imce
  Powered by
Imce 3.11a  © 2017, Pavel Formánek, Institute of Thermomechanics AS CR, v.v.i. [generated: 0.0112s]